Book Now!

 

 

We have noticed this post on How to Install a Bathtub directly below on the net and figured it made good sense to write about it with you here.

Setting up a tub isn't precisely brain surgery, yet it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently accessible, the task can relocate rapidly; if you have to open a wall surface to get rid of the old tub as well as position the brand-new bath tub, the job is much harder. In either case, the task is within a residence handyman's abilities, although you will require an assistant to move out the old tub and also embeded in the new one. Make sure you have actually certified yourself for the job and fit attempting it. As opposed to employing a professional to take over a halfway-completed task, it is much better to think about employing one prior to you begin. Chances are you might need a professional plumber to make tube links.
This short article will certainly assist you install a brand-new bathtub in your shower room if you have currently purchased a brand-new tub and also don't require to change the plan of your previous water supply pipes.
Your devices and product list ought to make up the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Removing Old Touches

If you require to change old taps with new ones as a part of your setup, after that the first thing you need to do is separate the water supply. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted access that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.

 

 

Fitting New Taps

If the tails of the new taps are plastic, then you will need a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and also the other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin making sure that the washers are in place between the faucet and also the sink. Safeguard the faucet in position with the producer offered backnut. Once the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former type should be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Setting up the Tub

Using both wood boards under its feet, put the bathtub in the required placement. The wood boards are useful in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four small factors.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by inspecting the level as well as changing the feet on the bath tub up until the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable faucet port to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the supply of water and examine all joints as well as brand-new pipework for leakages and tighten them if essential. Fill the bath tub and also inspect the overflow outlet and also the typical electrical outlet for leaks.
Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub ought to wait till the bathtub has actually been used a minimum of when as this will resolve it right into its final setting.

 

 

Preparing for the Setup

To start with, the supporting framework provided with the bath must be fitted (if called for) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is essential to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible tap ports to the bottom of both taps using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.

 

 

Tiling Around the Bathtub

In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a stiff seal, triggering the water to permeate the wall surface in between the bath as well as the tiling, resulting in problems with moisture as well as possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your components as well as installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the tub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can fracture rather very early if you do not take into consideration this motion before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly offered on the market. It is advisable to fit the floor tiles making use of water-resistant or waterproof glue and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As an avid person who reads on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I thought sharing that article post was a good idea. If you please take a moment to distribute this page if you liked it. Thanks for your time. Kindly come by our website back soon.

Book An Estimate Now